Eusso Super-G Betriebsanweisung

108Mbps Super-GTMWireless LAN Access Point User Guide

CONFIGURING THE WIRELESS LAN ACCESS POINT The Wireless Access Point has a Web GUI interface for the configuration. The AP can be configured through th

Main Screen of the Access Point The screen will show the status of the AP when you login to the AP. There are seven main functions included in the to

Wizard Setup wizard is provided as the part of the web configuration utility. User can simply follow the step-by-step process to get Access Point con

Step 3: Set WEP Encryption If user wants to enable WEP, please click “Enabled”. Then, select the key size of WEP encryption and enter the key value i

Status This page as below shows the following information. Firmware Version: Shows the current firmware version and released date code. LAN: Shows t

Basic Setting This is the page allow user to change the access point settings. . AP Name: The name of the AP, which can be used to identify the Acces

Note: When the WEP security is enabled, all the wireless clients that wish to connect to the Access Point must also have WEP enabled with the identic

WPA / WPA2: If WPA or WPA2 is selected, the below screen is shown. Please set the length of the encryption key and the parameters for the RADIUS se

IP Setting This page allows user to configure the IP and DHCP settings of the Access Point. The default IP address of this access point is 192.168.1

Advanced Setting This page contains configurations for advanced users, which the change reflects the wireless performance and operating modes. AP Mo

Regulatory notes and statements Wireless LAN, Health and Authorization for use Radio frequency electromagnetic energy is emitted from Wireless LAN dev

AP Client mode Configure the AP to AP Client mode; the AP will be a wireless Ethernet adapter transforms any Ethernet-enabled devices to have the w

WDS: Select the client mode connection method for WDS, Clone MAC or Proxy. WDS: Through this client mode AP, multiple users are allowed connecting t

Multiple Bridge mode Configure to the multiple bridge mode; these APs will be a LAN to LAN wireless Ethernet bridge between two or more separated

Repeater mode Configure the AP to Repeater mode; the AP will be a wireless LAN repeater that will be extended the WLAN coverage range. Note: The

DTIM Interval: This value indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clien

Security This page is where user configures the security features supported by this Access Point. Password: Allow user to change the new login passw

Tools Four functions are provided in this page, Backup, Restore Settings, Restore default settings and Firmware Upgrade. Backup Settings: Click on “

Community: SNMP system name for exchanging SNMP community messages. The name can be used to limit SNMP messages passing through the network. The defa

TECHNICAL SPECIFICATIONS General Standards IEEE 802.11b IEEE 802.11g IEEE 802.3u 10/100BASE-TX Fast Ethernet Signal Type: DSSS (802.11b) OFDM (802.1

Physical and Environmental DC inputs DC 7.5V /1A Temperature Operating: 0 ~ 40 oC, Storage: -10 ~ 70 oC Humidity Operating: 10% ~ 90%, Storage:

FCC Radio Frequency Exposure statement This Wireless LAN radio device has been evaluated under FCC Bulletin OET 65 and found compliant to the requirem

Safety Information Your device contains a low power transmitter. When device is transmitted it sends out radio frequency (RF) signal. CAUTION: To main

TABLE OF CONTENT About This Guide...

ABOUT THIS GUIDE Congratulations on your purchase of this 108Mbps Super-G Wireless LAN Access Point. This manual helps to features the innovating wire

UNPACKING AND SETUP This chapter provides unpacking and setup information for the Access Point. Unpacking Open the box of the Access Point and careful

HARDWARE INSTALATION Front panel The figure below shows the LED Indicator of the Wireless LAN Access Point. Power: This indicator lights green when t

Ethernet port Ethernet port with 10/100Mbps Fast Ethernet connections, connect this port to switch/hub. Reset The Reset function is to reset the setti